Gerber Center-Drive Multitool Review | The Drive


Getting After It with the Gerber Center-Drive Multitool

  • Good: Large multi-tool that provides good leverage; knife is sharp and bigger than the one on most multi-tools; 12 included bits fit common-sized bolts and screws.
  • Bad: Big equals heavy, with an actual weight of 9.9 ounces; lacks a level of refinement you’d expect at this price.
  • Check Latest Price 

Changing out the gas struts for the rear window of my Honda Element, the pliers were thick and blunt at their tips—ideal for grabbing hold of the clip I needed to pull out. Interestingly, the nail puller turned out to be the perfect tool for getting underneath the clip and getting it out far enough that I could then use the pliers.

The knife is a three-inch blade. It cut through zip ties and rubber hoses with no issues. The steel is 420H Stainless, which is solid, medium-grade steel. The blade came well-sharpened and kept its edge with repeated use.

The length of the bit driver proved useful as I was reinstalling some bolts on the side cover of my Yamaha XS 400. It made it easier to get around some of the shapes, like the clutch hub, so I could just continue to rotate the tool rather than have to restart every quarter-turn as I would have with a smaller multi-tool.

Of note, at the base of the pliers are replaceable carbide wire cutters.  Feel free to cut away at safety wire, wiring harnesses, and other items knowing that when they dull, you can change them out with a small Torx screw.

The file included in multitools can often be of questionable use. To test this one I went into the engine bay of my Honda Element and decided to tackle a couple of rough finished pieces of metal that I’ve caught my hand on before. The file has two sides, a coarse side, and a fine side. The coarse side is fairly aggressive.  It took the edge off and smoothed out the metal around the radiator with just a few swipes. The fine side of the file didn’t take off much metal but could be useful for when you need to deburr something quickly. On a piece of scrap 2×4 in the garage, the coarse side was very effective at quickly taking down the material.

What’s Good About the Gerber Center-Drive Multitool

The advantage of the Gerber is that its size allows you to get more leverage on what you are working on. The jaws of the pliers grip strongly, and the larger cutting tools inside make quick work of zip ties and other materials.

The high-quality three-inch blade is also notable. In many multi-tools, the knife is a bit of an afterthought, be it in material, size, or sharpness. That is not the case here. A standard test for knife sharpness is to take a piece of paper and cut it at an angle while holding it. If it easily cuts paper, the blade is sharp. This one passed the test with flying colors.

While the knife is great, the bit driver is the real star of the show here. It extends to give you impressive reach: 3.5 inches from the pivot point of the tool to the tip of most of the bits. The driver is magnetized to hold bits in place, and the thickness of the tool means that you can get a good grip and apply solid torque where needed.

What’s Bad About the Gerber Center-Drive Multitool

At just under 10 ounces, this is a large and heavy multi-tool that lacks value at a price point of $115. Sure, it’s solid, pretty well-made right here in the U.S., and useful. But it is, in a word, massive. Any multi-tool I carry and use often needs to be lightweight and easy to tote around. This Gerber is not that.

It also lacks refinement, especially at this price. There’s friction in the mechanism to slide the pliers out; rather than a smooth glide, there is a good deal of resistance. In deploying the other tools, the story is much the same. There is an inconsistent amount of effort required. Some take less effort than others, but all of them lack a smoothness; you can feel the grit of metal surfaces that are not well finished up against each other. Perhaps with time and use, those surfaces will grind down the rough spots and actuation will require less effort but out of the box, it’s a bit sticky. For over a hundred bucks, we expect a bit more.

Our Verdict On the Gerber Center-Drive Multitool

If this Gerber looks like it fills a need for you, then you should buy it—but only where you’re confident it can be returned, because it won’t be for everyone. You’ll know quickly if this is the right multi-tool for you. 

It is extremely solid and robust. But its size, weight, and cost keep me from enthusiastically recommending it as an everyday-carry, go-to multi-tool. I don’t see it as an essential item of EDC—although it could come in handy if you stowed it in your glovebox.

Source Article

Next Post

Electrify America Is Phasing Out CHAdeMO Chargers, and That’s a Big Deal for Old EVs

Charging standards can be confusing to the new electric vehicle adopter. There’s a flurry of acronyms, numbers, and difficult-to-pronounce names which can seem overwhelming when beginning the journey to electrification. Maybe that’s why Tesla’s choice of a proprietary charging connector—combined with an aggressive rollout of fast-charging locations—makes more sense than […]

You May Like